![]() Silicon Dust says the flashing LED means the tuner is "reserved or in use by another program" and cannot stream. Assuming you have a good backup of your external library, move to the next step. Navigate to this folder in Finder and you should see a bunch of backup files with the Library name in their file name. Last detail, when I had the problems with the W7MC install, and also now with the new W11/WMC 8.8.5 install, in both cases when WMC is trying to tune or scan for channels, one or both tuner LEDs on the HDHomeRun(s) will flash rather than be lit steadily as they always were in the past. Go find where backups are stored: Tools > Options > File Location > Program Files > Library Backups. I could do a "Digital TV signal strength" test and it would even see strong signals on channels but still not display them. I need to mention that starting perhaps around when the MS guide data stopped in early 2020 or maybe before, I could no longer view live TV or record any channels in the Windows 7 MC installation on the same hardware. maybe other steps that I should have written down. ![]() uninstalled the HDHomeRun (viewer) program and rebooted the computer and tuner, in case that program was not "releasing" the tuners for WMC, then did another "scan for more channels" I am not sure if this is causing an issue or not. I should state, that I am running a Test version of their new application HDHomeRun DVR on the same hardware. network three (3) Tuner within your application. tried connecting the HDHomeRun directly to the computer with a fixed IP address and Ethernet cable (and another run of HDHomeRun Setup) I am not able to install the HDHomeRun ext. tried my other original HDHomeRun (after another reinstall and channel scan for it) tried a replacement power supply for the HDHomeRun turned off the Windows Firewall and re-ran the channel scan re-ran WMC TV Setup with and without accepting the Guide terms (of course, it found no data) check that WMC and HDHomeRun services were running verify Network Discovery is turned on and it is a private network rerun the HDHomeRun Setup, including uninstall and reinstall, then do a "scan for more channels" I have tried these steps to solve the problem, without success: First try using the up or down arrow of the D pad. There are two ways to access the record engine from live tv. Open the HDHR app on your client device to live tv. I reviewed all the DLNA settings and confirmed that the firewall is disabled. However the system does not recognize my HDHomerun tuners, which work fine on the Windows version. When I did my TV setup, it found the two HDHomeRun tuners, but when I did the channel scan, it found no channels. You can check that by opening where you should see any SD tuners listed and one HDHomerun RECORD, all will be in their own access box. I just installed the 27.0.62 Silicon/Intel build for the first time. I have an original HDHomeRun Dual ATSC tuner, and I did the latest Silicon Dust upgrade and channel scan, and it works fine in the HDHomeRun TV program. Here is my problem: I built a fresh install of Windows 11 with WMC version 8.8.5 using an Athlon 64 X2-4400 motherboard with 4 GB RAM and 120GB OS/4TB data hard drives (the same hardware as my Windows 7 WMC setup for several years but with 2GB more RAM). Thank you to the new forum owners for creating this new version! (I'm using the iPad version)ģ.I was a member at the old Green Button, I just got back into WMC after a couple of years. tracks) - the grid thumbnail display would be ideal for folders/containers and for photo and video items. Only display items in a list if the items are individual audio nodes (i.e. Instead of displaying items in a list with a lot of wasted space to the right, can you display slightly larger thumbnails in a grid (say 4 or 5 across)? I know you might run into problems with the length of the caption, but maybe the font size can be reduced if the text is too large to fit underneath the thumbnail. I even tried using a different router, etc. I did a full install of W7 today and clean install Media Center - and this also DID NOT WORK - has the same issue. A double tap opens the folder but a single tap/hold pops up the Add menu whether it's a folder or a node item.Ģ. If you select it with Media Center, the HDHomerun shows a tuner in use and the status channel shows the correct channel but the channel does not display in Media center. Instead of the Plus button to select an item, can this be done by a simple press on the item thumbnail itself. Very nice app, thank you! Looking for an alternative to PlugPlayer, which works well but has an idiosynchratic way of selecting items.ġ.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |